Availability: Automatic internal bypass Supplies utility power to the connected loads in the event of a UPS overload condition or fault. Scalable run time Allows additional run time to be quickly added as needed. Intelligent battery management Maximizes battery performance, life, and reliability through intelligent, precision charging. Hot-swappable batteries Ensures clean, uninterrupted power to protected equipment while batteries are being replaced Automatic restart of loads after UPS shutdown Automatically starts up the connected equipment upon the return of utility power. Temperature-compensated battery charging Prolongs battery life by regulating the charge voltage according to battery temperature. Manageability Network manageable Provides remote management of the UPS over the network. Infra StruXure Manager Compatible Enables centralized management via the APC Infra StruXure Manager. Smart Slot Customize UPS capabilities with management cards. LED status indicators Quickly understand unit and power status with visual indicators. Serial Connectivity Provides management of the UPS via a serial port. Adaptability: Plug-and-Play external batteries Ensures clean, uninterrupted power to the loads when adding extra run time to the UPS. Rack/Tower convertible Protects the initial investment in the UPS when migrating from tower to rack-mount environment. Flash upgradeable firmware Install maintenance releases of firmware remotely using FTP. Serviceability: User-replaceable batteries Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR) Automatic self-test Periodic battery self-test ensures early detection of a battery that needs to be replaced. Predicitive failure notification Provides early-warning fault analysis ensuring proactive component replacement. Disconnected battery notification Warns when a battery is not available to provide backup power. Audible alarms Provides notification of changing utility power and UPS conditions Protection: Frequency and voltage regulation Gives higher application availability by correcting poor frequency and voltage conditions without using the battery. Power conditioning Protects connected loads from surges, spikes, lightning, and other power disturbances. Input power factor correction Minimizes installation costs by enabling the use of smaller generators and cabling. Generator compatible Ensures clean, uninterrupted power to protected equipment when generator power is used. Cold-start capable Provides temporary battery power when the utility power is out. Resettable circuit breaker Easy recovery from overloads; no need to replace a fuse. Safety-agency approved Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment. Output Voltage Distortion Less than 3% Output Frequency (sync to mains) 50/60 Hz +/- 3 Hz user adjustable +/- 0.1 Crest Factor 3 : 1 Waveform Type Sine wave Output Connections (1) Hard Wire 3-wire (H N + G) (1) Hard Wire 5-wire (3PH + N + G) Efficiency at Half Load 94% Bypass External Static Bypass,Internal Bypass (Automatic and Manual),Optional External Bypass Input Nominal Input Voltage 230V Input Frequency 50/60 Hz +/- 5 Hz (auto sensing) Input Connections Hard Wire 3 wire (1PH+N+G) Hard Wire 5-wire (3PH + N + G) Input voltage range for main operations 160 - 280V Other Input Voltages 220,240,400 Maximum Input Current 83A Input Breaker Capacity 100A Input Total Harmonic Distortion Less than 5% for full load Batteries & Runtime Battery Type No internal battery - uses external battery system Extended Run Options Communications & Management Interface Port(s) DB-9 RS-232,RJ-45 10/100 Base-T,Smart-Slot Pre-Installed SmartSlot™ Cards AP9619 Control panel Multi-function LCD status and control console Audible Alarm Audible and visible alarms prioritized by severity Emergency Power Off (EPO) Yes Surge Protection and Filtering Filtering Full time multi-pole noise filtering : 0.3% IEEE surge let-through : zero clamping response time : meets UL 1449 Physical Maximum Height 263.00 mm Maximum Width 432.00 mm Maximum Depth 773.00 mm Rack Height 6U Net Weight 68.00 KG Shipping Weight 90.50 KG Shipping Height 622.00 mm Shipping Width 610.00 mm Shipping Depth 1003.00 mm Color Black Units per Pallet 1.00 Environmental Operating Environment 0 - 40 °C Operating Relative Humidity 0 - 95% Operating Elevation 0-3000 meters Storage Temperature -15 - 45 °C Storage Relative Humidity 0 - 95% Storage Elevation 0-15000 meters Audible noise at 1 meter from surface of unit 50.00 dBA Online Thermal Dissipation 2216.00 BTU/hr Conformance Regulatory Approvals EN/IEC 62040-2,EN/IEC 62040-1-1 Standard Warranty 2 years repair or replace.